Cu掺杂对有序Sr3YCo4-xCuxO10.5+δ多晶的结构与物理性能的影响

采用固相反应法制备了四方Sr3YCo4-xCuxO10.5+δ(x=0~1.0)多晶。用热重-差示扫描量热分析,X射线衍射研究了多晶的有序化相变及结构。在固溶范围内(x=0~0.4),观察到有序峰(103)和(215),说明四方Sr3YCo4-xCuxO10.5+δ多晶为超结构,这是由于合成时在1000℃以上发生了吸氧(δ)有序化相变；当x=0.6~1.0时,978℃时在晶界处形成了单斜杂相,破坏了Sr3YCo4-xCuxO10.5+δ多晶的有序。当x=0~0.4时,多晶呈半导体输运行为。随着Cu掺杂量的增加,Co4+提供的空穴载流子浓度增大,电阻率明显下降；由于Cu的固溶,自旋熵增加,载流子浓度和自旋熵的共同作用使x=0~0.2多晶的热电势不变,x=0.4的热电势降低。并且Cu掺杂导致的晶格畸变使Co3+离子由高自旋态转变为高/低自旋混合态,磁化强度和铁磁转变温度(Tc)降低,磁结构由G-型反铁磁转变为铁磁。在进行二次烧结后,300K时电阻率明显降低,热电势为一次烧结的2倍,可能是二次烧结使多晶的有序化程度增大,提高了铁磁有序排列。     

空中分布式作战概念及关键技术分析

空中分布式作战是美军为应对“反介入/区域拒止”挑战提出的重要作战概念，具备分布式、智能化、高动态、大规模等特点，是未来美军空中作战平台在体系支持下作战样式的发展趋势。首先，按照提出时间梳理了美军空中分布式作战概念及典型研究项目，分析了空中分布式作战内涵、特点、工作机理以及发展趋势；然后，结合空中作战平台典型构型，提出了全域作战体系支撑下的空中分布式作战样式设想；最后，设计了空中分布式作战体系技术框架，并讨论了相应的关键技术。     

Direct ink writing of vancomycin-loaded polycaprolactone/ polyethylene oxide/ hydroxyapatite 3D scaffolds

Novel inks were formulated by dissolving polycaprolactone (PCL), a hydrophobic polymer, in organic solvent systems; polyethylene oxide (PEO) was incorporated to extend the range of hydrophilicity of the system. Hydroxyapatite (HAp) with a weight ratio of 55–85% was added to the polymer-based solution to mimic the material composition of natural bone tissue. The direct ink writing (DIW) technique was applied to extrude the formulated inks to fabricate the predesigned tissue scaffold structures; the influence of HAp concentration was investigated. The results indicate that in comparison to other inks containing HAp (55%, 75%, and 85%w/w), the ink containing 65% w/w HAp had faster ink recovery behavior; the fabricated scaffold had a rougher surface as well as better mechanical properties and wettability. It is noted that the 65% w/w HAp concentration is similar to the inorganic composition of natural bone tissue. The elastic modulus values of PCL/PEO/HAp scaffolds were in the range of 4–12 MPa; the values were dependent on the HAp concentration. Furthermore, vancomycin as a model drug was successfully encapsulated in the PCL/PEO/HAp composite scaffold for drug release applications. This paper presents novel drug-loaded PCL/PEO/HAp inks for 3D scaffold fabrication using the DIW printing technique for potential bone scaffold applications.     

Simultaneous fractionation of multiple classes of polyphenols from honeybush tea using solid-phase extraction

The structural diversity of polyphenols and the inherent limitations of current extraction techniques pose a challenge to extract polyphenols using a simple and green method. Hence, in this study, a method was developed to simultaneously fractionate multiple classes of polyphenols by only varying ethanol-water solutions. Honeybush tea, which is rich in polyphenols, was selected as a model for this study. Solvent extraction followed by solid-phase extraction (SPE) was developed to obtain a polyphenol-rich fraction from six honeybush samples. Based on a gradient elution programme (10%, 30%, 50%, 70% and 90% (v/v) ethanol-water solution) of SPE, the Strata X cartridge showed a better recovery of most targeted polyphenols under 0.9 mL of the drying volume and 1 mL min⁻¹ of the dispensing speed. The elution programme for fractionating most polyphenols was as follows: single elution with 50% ethanol, followed by twice elution with 70% ethanol. The antioxidant capacity was used to analyse the differences among the polyphenol-rich fractions from six honeybush samples. Principal component analysis (PCA) revealed that unfermented C. genistoides (GG) has the greatest antioxidant capacity among the honeybush species studied. Additionally, mangiferin, isomangiferin and vicenin-2 were the main contributors to the antioxidant capacity in six honeybush fractions according to the correlation study.     

行李箱外板浮动整形模设计

介绍了某轿车行李箱外板的翻边侧整形模设计过程,行李箱外板的侧法兰翻边上存在凹包,其翻边方向和凹包成形方向不同,常规需要2道工序分别完成翻边和凹包成形。该模具突破了传统的设计结构,在翻边机构中设置了凹包成形机构,将2个不同方向的成形复合到1道工序中,减少了模具数量,降低了冲压成本和工装成本。     

CFETR水冷陶瓷增殖剂包层模块产氚率实验验证

水冷陶瓷增殖剂（WCCB）包层作为中国聚变工程试验堆（CFETR）候选包层之一，承担着氚增殖、核热提取、屏蔽等重要涉核功能，其中子学设计的可靠性直接影响CFETR氚自持目标的实现。为验证中子学设计工具，即MCNP和FNEDL3.0数据库，在WCCB包层中子学设计中的可靠性，基于研制出的WCCB包层模块，在DT中子环境下开展中子学实验，对以产氚率（TPR）为代表的中子学参数进行了模拟值（C）和实验值（E）对比分析。结果表明，模块中轴线位置处TPR的C/E为0.97?1.08，而模块边缘位置处TPR的C/E为0.65?0.82；模块钛酸锂层边缘区197Au（n，γ）198Au反应率的C/E为0.72?0.90，表明模块边缘区存在非期望的散射中子，导致该区TPR模拟值和实验值偏离较大。